Browse through the following possible scenarios and click the most appropriate link for your current issue.
- Using your cleaner
-
Extracting the the power cord
- extract power cord and plug it into the power supply. Do not pull the cord beyond the red marker.
-
adjusting the telescopic tube
- Adjust the telescopic tube to the desired height by holding the handle and moving the central hand grip up or down.
-
Selecting the carpet height control
- Select carpet care control height by pressing the pedal in the nozzle.
Hard Floor – Brushes are lowered to protect the floor.
Carpet – Brushes are raised for the deepest clean.
-
Switching the cleaner on
- Switch the cleaner on by pressing the on/off Button on the cleaner main body.
-
Adjusting the suction
- Adjust the suction by sliding the suction regulator to the desired level.
-
At the end of use
- Switch off at the end of use by pressing the on/off Button. Unplug and press the cord rewind button to wind the power cord back into the cleaner.
-
Storing your appliance
- To store your cleaner adjust telescopic tube to the lowest height setting and park the nozzle in the park position on the cleaner main body.
- Accessories
-
3 in 1 tool
- Ccombines several functions in one, with maximum flexibility by the rotating body. Reach into awkward areas by rotating the body. The 3 in 1 tool can be stored neatly underneath the hose handle.
-
Crevice tool
- For corners and hard to reach areas.
-
Furniture nozzle
- For soft furniture and fabrics
-
Dusting brush
- For bookshelves, frames, keyboards and other delicate areas. To extend
the brushes push the button on the body of the tool.
-
Parquet caresse tool
- For parquet floors and other delicate floors.
-
Allergen Remover Turbo Nozzle
- Use the turbo nozzle for deep cleaning on carpets.
-
Allergen Remover Mini Turbo Nozzle
- Use the mini turbo nozzle on stairs or for deep cleaning on textile surfaces and other hard to clean areas.
-
Important
- IMPORTANT: Do not use the turbo and mini turbo nozzles on rugs with long fringes, animal hides and carpet pile deeper than 15mm. Do not keep the nozzle stationary while the brush is rotating.
- Emptying the dust container
-
Releasing the container
- Release the container carry handle by lifting the centre latch to detach the dust container from the main cleaner and pull upward to remove.
-
Emtying the container
- Hold the dust container over a bin with one hand and with the other pull the dust container catch to open the door and empty.
-
Re-fitting
- close the dust container door and refit to the cleaner main body. To lock in place push the container carry handle down until the latch connects with the main body of the cleaner. Once correctly retained the carry handle will sits flush with the top of the cleaner.
- Cleaning the washable filters
-
Overview
- The cleaner is fitted with a blue hepa filter pack. To maintain optimum cleaning performance
regularly remove the the filters and tap against the side of the bin to release dust.The filters should be washed every 3 months or when the filter has excessive dust level.
IMPORTANT: Regularly check and maintain the filters.
IMPORTANT: Always ensure the filter pack is fully dry before use.
- Access the filters
-
Step 1
- Unlock the filter door by pulling the filter latch upwards. Oopen the filter door.
-
Step 2
- Remove the filter pack by pressing down on the retainer catch to release. The filter pack will pop up. Slide the filter pack out.
-
Step 3
- Unlatch the filter pack frame.
-
Step 4
- Remove the foam micro filter from the pack.
-
Step 5
- Gently tap and wash the grey foam micro filter attached to the filter frame using warm water. Do not use hot water or detergents. Remove excess water from the filter and leave to dry fully before re-using.
-
Step 6
- Gently tap and wash the Blue HEPA filter unit. Do not use hot water or detergents. Remove excess water from the filter and leave to dry fully before re-using.
-
Step 7
- Reassemble to filter pack once fully dry and refit to the cleaner. Press on the top of the filter to ensure it clips back into place.
- Cleaning the cyclonic unit
-
Step 1
- Remove dust container from the cleaner by releasing the container carry handle to detach the dust container from the main cleaner and pull upward to remove.
-
Step 2
- Place the bin on a flat surface and unclip the clips from either side of the dust container.
-
Step 3
- Using the bin handle lift the bin upper section containing the cyclonic unit from the lower section.
-
Step 4
- Use a cloth to remove excessive dust from the cyclone unit’s surface.
-
Step 5
- Reassemble the bin upper section taking care to align the arrows on the container. Push clips back to fully close the bin.
-
Step 6
- Refit the dustbin to the cleaner. To lock in place push the container carry handle down until the latch connects with the main body of the cleaner. Once correctly retained
the carry handle will sits flush with the top of the cleaner.
- Problem with cleaner
-
Electrical supply
- is there a working electricity supply to the cleaner? Please check with another electrical appliance.
-
Cyclonic dust container
- is the cyclonic dust container over-filled? Please refer to ‘cleaner Maintenace'
-
Blocked filter
- Is the filter blocked? Please refer to 'Cleaner Maintenance’.
-
blocked hose
- is the hose or nozzle blocked? Please refer to ‘Removing a blockage from the system’.
-
Cleaner overheated
- Has the cleaner overheated? if so, it will take approximately 30 minutes to automatically reset.
- Removing a blockage
-
Dust container
- Check if the dust container is full. If so refer to ‘Emptying the dust container'.
-
Do the filters need cleaning
- Do the filters need cleaning? Iif so refer to ‘Cleaning the washable filters’.
-
Checking for blockages
- Check if there is any other blockage in the system - Use a rod or pole to remove any blockage from the extension tube or flexible hose.
-
checking the pre-motor filter
- check if pre-motor filter is fitted and filter door is closed
-
Cyclonic unit
- Check if the cyclonic unit needs to be cleaned. Refer to ‘Cleaning the cyclone unit’